Censer bearers rules

Skaven

Moderator: Hoax

Zablokowany
Awatar użytkownika
Lazur
Niszczyciel Światów
Posty: 4573

Censer bearers rules

Post autor: Lazur »

Mógłby ktoś wpisać tu zasady censer bearerów po angielsku, najlepiej jak przepisze z angielskiego booka:)
Będe zobowiązany.
Obrazek

Awatar użytkownika
Cosmo
Oszukista
Posty: 886
Lokalizacja: Zabrze

Post autor: Cosmo »

To raczej do poczatkujacego generala powinno isc..

Weapon: Plague Censer.

Scurry Away!, Strength in Numbers, Frenzy, Hatred, Skirmish.

Plague Disciples: A unit of Plague Censer Bearers that is within 6" of a unit of Plague Monks may use the rank bonus of the Plague Monks to modify their own Leadership. If the Censer Bearers are within 12" of a Plague Furnace they are Stubborn.

Awatar użytkownika
Lazur
Niszczyciel Światów
Posty: 4573

Post autor: Lazur »

Nie wiedziałem gdzie to umieścić. Dzięki Cosmo a jakbym mógł jeszcze zasade samego censera
Obrazek

Myth
Szef Wszystkich Szefów
Posty: 3175
Lokalizacja: Warszawa, 8 Bila

Post autor: Myth »

PLAGUE CENSER
The dreaded plague censer is a weapon that is only borne by the degenerate ratmen of Clan Pestilens. A plague censer is a Warpstone Weapon and counts as a flail with the following additional rules to cover the deadly fog that surrounds such vile weapons: At the beginning of any Close Combat phase all models (friend or foe) in base contact with one or more models bearing a plague censer must take a Toughness test or suffer a single wound with no armour save allowed. This means that a model need only take a single such Toughness test in each round of combat, regardless of the number of plague censers that it might be adjacent to. Remember all such wounds count for combat resolution. Wounds caused by the fog are resolved before Impact Hits, issuing challenges, and revealing Assassins. All Clan Pestilens models, that is, Plague Monks, Plague Priests, Plague Censer Bearers, Plague
Furnace, Lord Skrolk, and the Plagueclaw Catapult suffer a wound only on a roll of 6.
Proszę bardzo.
www.marnadrukarnia.com - druki 3D i turnieje.

Awatar użytkownika
Lazur
Niszczyciel Światów
Posty: 4573

Post autor: Lazur »

Dzięki
Obrazek

Awatar użytkownika
Kefas
Masakrator
Posty: 2586

Post autor: Kefas »

lazurrr... no ja Cię proszę! jak chciałeś zadać takie banalne pytanie to mogłeś jak Cosmo pisał do "początkującego gjenjirała" wrzucić... bo co ma niby ten temat wnosi? nic
Następnym razem zastanów się 2x zanim będziesz miał zamiar założyć jakiś temat na tym już tak bardzo zaśmieconym dziale. pozdro

Awatar użytkownika
Lazur
Niszczyciel Światów
Posty: 4573

Post autor: Lazur »

Już napisałem, że nie wiedziałem gdzie to umieścić na przyszłość będe wiedział. Raz jeszcze dziękuje Cosmo i Mythowi za cytat z booka a Kefasowi za... hmm... krytyke :P
Obrazek

Zablokowany